Short XLR to Lemo cable for use with Schoeps CCM Lemo mics and Rycote Cyclone.
Short XLR to MZL cable for use with the Sennheiser MKH 8060 and Rycote Cyclone.
Short XLR cable for use with Cyclone windshields.
Short right-angle XLR cable with integrated low cut filter.
18" right-angle XLR cable with integrated high pass filter.
Fits any 3/8" threaded boom pole, mic stand, or shock mount.
XLR unbalanced line output cable for G3 receivers.
Removes ground loop hum, mode noise & differentially induced hum in one device.
One foot cable for recording from an XLR mic on a mobile device. 3.5mm monitoring tap included
No connectors. Requires soldering.
Can be set to 15, 20, or 25 dB. Passes phantom power
Used to connect balanced and unbalanced devices having different signal levels or impedances.
Helps to eliminate electrical and mechanical noise in an audio system such as 60Hz electrical hum from AC power lines, low-frequency rumble caused by wind noise or air conditioning system, and stage/floor noise transmitted to a microphone through the microphone stand
Converts balanced line level signals to microphone level (50dB attenuation)
Reverses the phase (polarity) of a balanced audio signal. In line switch permits selection of normal or reversed polarity for comparison purposes.
RF filter, XLR in/out. Passes phantom power
700 Hz microphone-level signal
Transforms your XLR microphone to a USB microphone for digital recording.
USB-C to 2x USB-A Y-cable for powering the MixPre-3 or MixPre-6 recorder from a computer.
Powers a PIX-E5, PIX-E5H or PIX-E7 monitor from a Anton Bauer camera battery.
Hirose 10-pin to two-XLR (balanced L/R) and 3.5 mm plug (442 / 552 Stereo Return A) breakout cable, 24-inch; includes in-line 20-foot extension cable; for 442 / 552 mixers.
Balanced TA3 outputs to balanced XLR inputs for use with Sound Devices 633, 664, and 688 production mixers. Package of two.
Balanced XLR outputs to balanced TA3 inputs for use with Sound Devices 633, 664, and 688 production mixers. Package of two.
For 552, 664, MixPre, MixPre-D, or MP-2 tape output to 442/302 mix in.
Time code to camera jamming for Sound Devices 633, 664, and 688 production mixers.
For jamming time code to equipment with XLR connectors.
Hirose HR10-7P-4P compatible connector.
For use with Zaxcom Nomad, Maxx, RX-12, Sound Devices 5, 6, and7 series, 302, MixPre (v2), 442, Lectrosonics Octopack, Quadpack, and more.
For use with SR receivers, SM BattELIM, and Venue.
For use with Lectrosonics 100, 200, 400 series receivers and ISO9VOLT battery eliminator.
For Sound Devices 688, 664, 633, 552, 700 Series, 302, MixPre (v2), 442, MM1 (v2); Lectrosonics Quadpack; and Zaxcom Nomad & Maxx.
Connects Tentacle Time Code Generator to iOS device for recording time code or MovieSlate.
Bidirectional cable to feed time code from your Tentacle to any device that uses a BNC time code in/out connector and vice versa, featuring a 90° right angle BNC connector.
Cable to feed timecode from your Tentacle to any device that uses a 1/4" jack input connector.
Cable to connect Tentacle to GoPro 3/4 Cameras. Timecode on left channel, build-in mic signal on right channel.
Connects Tentacle Time Code Generator to another Tentacle or a DSLR.
Connects Tentacle Time Code Generator to RED Cameras, excluding RED One.
Cable to feed time code from your Tentacle to any device that uses a standard LEMO 5-pin connector.
Connects Tentacle with Alexa Mini camera.
Connects Tentacle with a Sound Devices 552 audio recorder.
Cable to feed time code from your Tentacle to any device that uses a standard XLR input connector.
[email protected] (212) 629-9430[email protected] (404) 855-2255